City of the Dead

Graveyards can be tricky terrain pieces to build.  They have a lot of fiddly bits that become very delicate and damage prone.  For my fantasy terrain box, that's one hassle I'd like to avoid, so I just bought a resin graveyard from Monday Knight Productions.  This piece measures four inches on each side, and with all those lines of tombstones, you need to be careful how it affects play.  Depending on the ruleset each lone of stones could act like a linear obstacle, or you could treat the whole piece as rough ground.

The piece is scaled for 15mm, but look how low that outer wall stands.  You could easily use this piece as a 10mm terrain piece, too.

As I was entering the tags for this post, it occurred to me that this piece is fairly setting and era independent.  People always have and always will die, and stone walls around the city of the dead crop up all over the place.  There is no reason that this piece couldn't be used on my sci-fi table with no changes, except that it will live in my fantasy box and I'm likely to forget about it when pulling out the sci-fi box.

A Meme For All of Us

Mined Out - Bloodstone Temple

Lead Mountain is tapped out.  There's no more gold in them thar hills.  How does that happen?  I mean, sure there are a few mounted Musketeers and an odd bit or bob that could use some paint, but I'm raring to add to the 15mm fantasy, and that means there's only one thing to do - hit the bits box!

One busted up Lion King CD, some card stock, a few wooden dowels and washers later and behold!  The lost Bloodstone Temple.  The round wooden disc under the sacrificial black stone might just hold the entrance to a lost tomb, but how to open it?  

This is one of those 'found mysteries' that make miniature wargaming so much fun.  I set out to make a set piece for a battle map, maybe a nice objective for two factions to war over, and the only decent stone that worked for a sacrificial altar was a little too slanted on one side.  Placing a wooden bit and painting it as a nice red granite slab elevated one end of the altar, but it also makes for the perfect covering for a short drop into a lost tomb.

More Fantasy Figures

Are these good guys or bad guys?  Sometimes it can be hard to tell.  They are all from the DemonWorld line of figures, that's for sure.  

Wizard, Barbarian Warrior 3, and Barbarian Princess

 That center figure could be a male or female.  You don't often see that kind of versatility.

These two fellows are the worst kind of good guys.  The one on the left is the Supreme Dark Lord, as evidenced by his shield emblem.  (It's actually a Dark Paladin figure from Ral Partha Europe.)  His minon, a Vile Faceless Minion, is a Black Knight figure.

One of the things that slowed my figure production over the last several months was the recording of a number of audio books for Castalia House, including a number of books by Martin van Creveld, a John C Wright book, and a pair of excellent short story collections.  Reading Jerry Pournelle in high school you would have bowled me over if you'd told me that one day I'd be professionally reading his works.  Truly an honor.  It's also an honor to work with Vox Day and serve alongside his Vile Faceless Minions.  So much so, that I stole their logos for the above figures.

But this isn't all about advertising my professional work using my hobby blog.  Rest assured, there is madness to my method.  The money earned from my audio work has been enough to fund a fairly major project that I'm excited to share with you lot.  I'm still in the planning, purchasing, and preparation phase, but rest assured that you're going to see some major new additions to the blog before too much longer.

Meanwhile, here are the SDL and his VFM, heading off into the sunset. 

Warren Abox Paints Again!

The year of our Lord Two Thousand and Seventeen has been one heckuva roller coaster, but things might just settle down around Chateau Abox.  Those of you that followed me over to the Castalia House Blog saw my little Three Musketeers Project, which (much to my regret) has yet to see any tabletime.  You also know that I've been busy launching a writing career using the name my long suffering parents bequeathed to me.  Add in a couple of other backstage projects and a long stint overseas, and my output has been astonishing.

The good news for fans of Warren Abox is that Castle Meatgrinder has a few new additions for team good, team evil, and team squishy moderate.  Let's take a look at the big bad boys that the PCs won't want to meet until after they have broken out the blue-covered Moldvay/Cook book.  All of the latest additions to the collection are DemonWorld figures, available through Ral Partha Europe.

Ogre chieftan (DI016C) on left.
Two armored ogres (4017A) on the right.
Barbarian Princess for scale.

This big bad demon is from the Icelords of Isthak lineup.  The official paintjob calls for blue and white, but you can make them a more generic demon with a different paint scheme.

Dai Re'Coon #1 (4213A)

More to come later.  Don't worry, you won't have to wait another seven months for an update.